Advanced Photography Course

Figure AI-1.--Silver recovery cartridge.

ELECTROLYTIC PLATING

An electrolytic plating silver recovery unit is more

complex than a silver recovery cartridge, but it is

actually much easier to operate and control than the

processing machines that generate the used solutions.
The initial cost is higher than a cartridge; however, the
cost is not exorbitant and the electrolytic plating unit
should be considered as the primary means for
recovering silver from fixers and bleach fixers. Navy
imaging facilities are not charged for silver recovery
equipment. Procedures for obtaining silver recovery
equipment are located in the Defense Reutilization and

Marketing Manual (NOTAL), DoD 4160.21-M.

The electrolytic plating method of silver recovery

uses two electrodes: a cathode and an anode. They are
placed in the silver bearing solution and an electric
current is passed between them, causing almost pure

silver to plate onto the cathode (fig. AI-2). The silver
recovery capacity of the unit is determined by the direct
current density and the size of the cathodes; that is,
(amperes) in relation to the surface area of the cathode.

Tank size is another measure of recovery capacity.

Smaller tanks have less plating capacity because of a

proportionately smaller cathode surface area.

Agitation

An agitation or recirculation system provides a

continuous supply of silver-laden solution to the
cathode. Without this system, the current density would
become too high for the amount of silver present in the
solution near the cathode and result in the formation of
silver sulfide. This silver sulfide decreases the
efficiency of the unit.

Cathode Design

The cathodes in various electrolytic plating units

vary in design. Some units have a simple flat plate;
others may have several circular disks mounted on a
shaft or use a rotating cylinder (fig. AI-3). Cathodes are
made of metal and there are two types: flexible and
nonflexible. The flexibility of the cathode makes it easy
to remove the silver flake. Those cathodes that are not
flexible can be tapped lightly on a flat surface to remove

AI-2

contents

Advanced Photography Course

<- previous page

next page ->


DOFMaster for Windows On-line Depth of Field Calculator DOFMaster for Mobile Devices On-line Depth of Field Table Hyperfocal Distance Chart Articles FAQ Recommended Books Support Contact Links Home As an Amazon Associate I earn from qualifying purchases.	contents <- previous page next page -> Figure AI-1.--Silver recovery cartridge. ELECTROLYTIC PLATING An electrolytic plating silver recovery unit is more complex than a silver recovery cartridge, but it is actually much easier to operate and control than the processing machines that generate the used solutions. The initial cost is higher than a cartridge; however, the cost is not exorbitant and the electrolytic plating unit should be considered as the primary means for recovering silver from fixers and bleach fixers. Navy imaging facilities are not charged for silver recovery equipment. Procedures for obtaining silver recovery equipment are located in the Defense Reutilization and Marketing Manual (NOTAL), DoD 4160.21-M. The electrolytic plating method of silver recovery uses two electrodes: a cathode and an anode. They are placed in the silver bearing solution and an electric current is passed between them, causing almost pure silver to plate onto the cathode (fig. AI-2). The silver recovery capacity of the unit is determined by the direct current density and the size of the cathodes; that is, (amperes) in relation to the surface area of the cathode. Tank size is another measure of recovery capacity. Smaller tanks have less plating capacity because of a proportionately smaller cathode surface area. Agitation An agitation or recirculation system provides a continuous supply of silver-laden solution to the cathode. Without this system, the current density would become too high for the amount of silver present in the solution near the cathode and result in the formation of silver sulfide. This silver sulfide decreases the efficiency of the unit. Cathode Design The cathodes in various electrolytic plating units vary in design. Some units have a simple flat plate; others may have several circular disks mounted on a shaft or use a rotating cylinder (fig. AI-3). Cathodes are made of metal and there are two types: flexible and nonflexible. The flexibility of the cathode makes it easy to remove the silver flake. Those cathodes that are not flexible can be tapped lightly on a flat surface to remove AI-2 contents Advanced Photography Course <- previous page next page ->	As an Amazon Associate I earn from qualifying purchases.
	WWW.DOFMASTER.COM © 2006 Don Fleming. All rights reserved.